DSRC devices
- Code: 10.UTPX.0100
-
Devices for checking the proper operation of DSRC modules of intelligent tachographs (1C).
According to the requirements of the EU Regulation 2016/799, one of the stages of smart tachograph inspection (1C) is to verify the correct operation of the tachograph DSRC module.
MATTNX DSRC Checker+
MATTNX DSRC Checker+ is a set that works independently of your tachograph tester. It is possible thanks to equipping it with the TachoDrive5 device with a built-in chip card reader.
The MATTNX DSRC Checker+ device will allow you to meet the above requirements. It is powered by a Li-Po battery which ensures operation for min. 1 business day. The operating time of the devices depends on the intensity of use.
The DSRC Checker is a handheld and peripheral device and must work with a control device to be checked.
Technical data:
|
|
Checker |
TachoDrive5 |
|
Supported tests |
RSSI - signal strength ECHO - frames sending and receiving test (100/1000) RTM - reading and decrypting data from tachograph using the workshop/control card |
|
|
Dimensions |
141 x 69 x 18 mm |
121,1 x 71,5 x 19,3 |
|
Weight |
150g |
215g |
|
Operating temp. range |
-20 ÷ +60 OC |
-5 ÷ +55 OC |
|
Storage temperature |
0 ÷ +45 OC |
-25 ÷ +70 OC |
|
Protection degree |
IP-65 |
IP-40 |
|
Port |
USB micro |
USB-C |
|
Card reader |
NO |
YES |
|
Working time on a fully charged battery |
1 working day |
1 working day |
MATTNX DSRC Tester
MATTNX DSRC Tester has a built-in microwave antenna with larger dimensions than the MATT DSRC Checker, so it can emit more power, and has a higher sensitivity of the radio path than the DSRC Checker device. It is powered by a high-capacity Li-Po battery, which ensures operation for min. 2 working days. The operating time of the device depends on the intensity of use. It is recommended to install the device on a stand or on a bracket fixed to the wall. The DSRC Tester is a radio device that must be controlled from the TachoDrive5 BT device or the UTPNX tester.
It is available in two configurations:
- MATT DSRC Tester (P/N: 10.UTPX.0101) as a device for UTPNX tester
- MATT DSRC Tester+ (P/N: 10.UTPX.0103) – stand-alone set, independent from the tachograph tester. The set is equipped with the TachoDrive5 BT device, having a built-in chip card reader and a BT module.
Technical data:
|
|
DSRC Tester |
UTPNX |
|
Supported tests |
RSSI - signal strength ECHO - frames sending and receiving test (100/1000) RTM - reading and decrypting data from tachograph using the workshop/control card |
|
|
Dimensions |
170 x 310 x 40 mm |
93 x 93 x 25 |
|
Weight |
1100g |
215g |
|
Operating temp. range |
-33 ÷ +55 OC |
-5 ÷ +55 OC |
|
Storage temperature |
0 ÷ +40 OC |
-10 ÷ +60 OC |
|
Protection degree |
IP-65 |
IP-40 |
|
Port |
SP13 7-PIN IP-68 |
USB-C |
|
Card reader |
NO |
YES |
|
Working time on a fully charged battery |
2 working days |
1 working day |